Reaction profiles during exhaust-assisted reforming of diesel engine fuels

Research output: Contribution to journalArticle

Standard

Reaction profiles during exhaust-assisted reforming of diesel engine fuels. / Tsolakis, Athanasios; Megaritis, Athanasios; Golunski, SE.

In: Energy & Fuels, Vol. 19, No. 3, 01.01.2005, p. 744-752.

Research output: Contribution to journalArticle

Harvard

APA

Vancouver

Author

Bibtex

@article{d3282ed250b342609be1cbb291acea05,
title = "Reaction profiles during exhaust-assisted reforming of diesel engine fuels",
abstract = "On-board hydrogen production by exhaust-assisted fuel reforming offers a potential route to diesel emission control. In this study, different reformer configurations with the same catalyst composition were tested, as well as three types of diesel engine fuel, under conditions designed to simulate low- and high-load engine operating modes. The reforming efficiency was dependent on the fuel type and followed the general trend of bioethanol > rapeseed methyl ester > low-sulfur diesel fuel. In each case, a characteristic axial temperature profile was established in the catalyst. The profile can be deconvoluted into three phases, corresponding to the consecutive occurrence of combustion, steam reforming, and water-gas shift. The relative contribution of each process not only responds to changes in the inlet conditions but also to the aspect ratio and form of the catalyst bed. The heat produced in the first phase must be effectively transferred to the endothermic and much-slower steam-reforming reaction, whereas in the final phase, heat must be lost to ensure that the thermodynamically limited water-gas shift reaction is favored.",
author = "Athanasios Tsolakis and Athanasios Megaritis and SE Golunski",
year = "2005",
month = jan,
day = "1",
doi = "10.1021/ef049727p",
language = "English",
volume = "19",
pages = "744--752",
journal = "Energy & Fuels",
issn = "0887-0624",
publisher = "American Chemical Society",
number = "3",

}

RIS

TY - JOUR

T1 - Reaction profiles during exhaust-assisted reforming of diesel engine fuels

AU - Tsolakis, Athanasios

AU - Megaritis, Athanasios

AU - Golunski, SE

PY - 2005/1/1

Y1 - 2005/1/1

N2 - On-board hydrogen production by exhaust-assisted fuel reforming offers a potential route to diesel emission control. In this study, different reformer configurations with the same catalyst composition were tested, as well as three types of diesel engine fuel, under conditions designed to simulate low- and high-load engine operating modes. The reforming efficiency was dependent on the fuel type and followed the general trend of bioethanol > rapeseed methyl ester > low-sulfur diesel fuel. In each case, a characteristic axial temperature profile was established in the catalyst. The profile can be deconvoluted into three phases, corresponding to the consecutive occurrence of combustion, steam reforming, and water-gas shift. The relative contribution of each process not only responds to changes in the inlet conditions but also to the aspect ratio and form of the catalyst bed. The heat produced in the first phase must be effectively transferred to the endothermic and much-slower steam-reforming reaction, whereas in the final phase, heat must be lost to ensure that the thermodynamically limited water-gas shift reaction is favored.

AB - On-board hydrogen production by exhaust-assisted fuel reforming offers a potential route to diesel emission control. In this study, different reformer configurations with the same catalyst composition were tested, as well as three types of diesel engine fuel, under conditions designed to simulate low- and high-load engine operating modes. The reforming efficiency was dependent on the fuel type and followed the general trend of bioethanol > rapeseed methyl ester > low-sulfur diesel fuel. In each case, a characteristic axial temperature profile was established in the catalyst. The profile can be deconvoluted into three phases, corresponding to the consecutive occurrence of combustion, steam reforming, and water-gas shift. The relative contribution of each process not only responds to changes in the inlet conditions but also to the aspect ratio and form of the catalyst bed. The heat produced in the first phase must be effectively transferred to the endothermic and much-slower steam-reforming reaction, whereas in the final phase, heat must be lost to ensure that the thermodynamically limited water-gas shift reaction is favored.

U2 - 10.1021/ef049727p

DO - 10.1021/ef049727p

M3 - Article

VL - 19

SP - 744

EP - 752

JO - Energy & Fuels

JF - Energy & Fuels

SN - 0887-0624

IS - 3

ER -